Home » 出版部会
Category Archives: 出版部会
Journal “Design Engineering” Vol.60, No.8 2025
Special Issue: Best Presentation Papers at Annual Conference on Spring and Autumn
Evaluation of an Elastic-plastic Transition of Mg Alloy Thin Plate Using Transmitted X-ray Diffraction
Yutaka YOSHIDA, Jun-ichi SHIBANO, Yosyua HONMA, Mitsuho INAGAKI, Kakeru TANDAI, 389
A Study of the Misfire Ratio and Emission Characteristics for Opposed Piston 2-Cycle Engine
Tadashige KAWAKAMI, 392
Out-of-Plane Bending Stress Intensity Factor Analysis of a Strip with Double-Edge Cracks Using Single-Element Strain Gauge
Jyo SHIMURA, Shigeru KUROSAKI, 395
Generation of Target Gait Using Generative Adversarial Network for Gait Training System
Ryoya OBA, Yusuke OSAWA, Keiichi WATANUKI, Kazunori KAEDE, 398
Design of Optical Lenses That Can Be Mounted on Small Satellites
Takashi HASEGAWA, Tomoyuki MIYASHITA, 403
Development of Humanoid Robot with Trunk Tilting Mechanism and Neck with Multiple Degrees of Freedom
(Design of the Head, Neck, Upper Limbs, and Trunk Mechanisms and Study of Neck Movement)
Chihiro KASAI, Ryo YOSHIDA, Kanta YAMAGUCHI, Keisuke KATO, 405
Development of an Active Seat Suspension Using a Magnetic Levitation System
(Effect of Steel Plate Thickness on Thrust Force)
Keigo IKEDA, Daigo UCHINO, Kazuki OGAWA, Ayato ENDO, Taro KATO, Takayoshi NARITA, Hideaki KATO, 409
Effect of Adjacent Fiber Orientation Angles of Blended Layers in Laminated Rectangular Plates
Michio INNAMI, 412
Effectiveness of a Spacer as a Separator for Pressurized Metered-Dose Inhaler (pMDI)
Kazuto NAKAGAWA, Fujio KOEDA, Reiko ITO, Yasuhiro GON, 417
Study of High-Friction Rubber Treads Using Negative Fluid Pressure Generated in an Expansion Gap
Arata ISHIZAKO, Aoi NISHIMOTO, Toshiaki NISHI, Takeshi YAMAGUCHI, 419
Analysis of the Influence on Competence Consciousness for Safe Driving by Experiencing Pedal Misapplication Using an Automobile Pedal Operation Simulator
Kazunori KAEDE, Kyonaka BABA, Masamitsu NAGAYOSHI, Kenya NAITO, Keiichi WATANUKI, 421
Study on Surging of Centrifugal Compressor
(Visualization of Flow Near the Outlet of Discharge Pipe by High-Speed Camera)
Akihiro SHIBUKAWA, Toshiyuki HIRANO, 426
Development of Robot Control by Muscle Movement Using Image Recognition
Kohei GOTO, Abhijeet RAVANKAR, Ankit A. RAVANKAR, 429
Paper (Published in J-STAGE)
Effect of Using Spacers for Pressure Metered-Dose Inhalers (pMDI) on Aerosol Particle Distribution
Kazuto NAKAGAWA, Fujio KOEDA, Reiko ITO, Yasuhiro GON, 435
Journal “Design Engineering” Vol.60, No.7 2025
Special Issue: Engineering Approaches Supporting Japanese Agriculture
Explanations
Challenges for Agricultural Robots Revealed by Automatic Cherry Harvesting Robots
Yuichi TSUMAKI, 343
Measuring Fruit Diameter Using an RGB-D Camera to Improve the Efficiency of Fruit Tree Management Tasks
Masaki ISHII, Teppei FUKUDA, 348
Wildlife Damage Control and Theft Prevention
(To Improve Food Self-Sufficiency)
Takahiro HIRAYAMA, 355
Novel Plant Disease Control and Growth Promotion Technology Using Atmospheric Pressure Air Plasma
Toshiro KANEKO, Shota SASAKI, 360
Papers (Published in J-STAGE)
Design of a Drone-mounted Pollinator Sprayer
Akihiro MIYASAKA, Kazuki YUGI, Yukihiro KANEKO, Keisuke YANAGI, 369
Research on the Vibration Characteristics of Thin Plate Structure as an Excitation Device for Audio Exciter
Katsuhiko KURODA, 379
Journal “Design Engineering” Vol.60, No.6 2025
Special Issue: Robotics and Mechatronics Development in Companies
Explanations
Robots as Parts
Yuki YOSHIDA, Yuta NAKAMURA, 295
Development of Autonomous Laparoscopic Camera Holding Robot
Kei TOMATSU, 303
Consideration on the Practical Use of KUROKO Crane Balancer: A Lightweight and Compact Air Balancer
Rina NISHIDA, Kazuhiro TSUKAHARA, Takumi KOJIMA, Shigeo HIROSE, 313
Paper (Published in J-STAGE)
Design and Development of Active-manual for Driver
(2nd Report, Identifying Cognition by Proficiency Comprehension)
Naoki NISHIMURA, Hitoshi SOMA, Yasushi YOKOYA, 319
Note (Published in J-STAGE)
Development of Digital Support Materials of Teaching for Education of Welding for Beginners
Tsuyoshi TAKAHASHI, Kazunori ISHITSUKA, Toshio KUSAKARI, Iwao ZANMA, Kouki NAGASAWA, 331
Journal “Design Engineering” Vol.60, No.5 2025
Special Issue: Efforts Related to Digital Manufacturing at Research and Development Institutes of Local Governments
Explanations
Research and Development of Digital Twin Technology and Study Group Activities
(Initiatives toward Social Implementation of Virtual Sensors)
Masahiro TAKANO, 239
Activities in the Kyushu Collaborative CAE Research Group
Tatsuya IZUMIKAWA, Toru TANAKA, Naoki IRIE, Masanori TSUCHIMURA, 244
Introduction to Digital Manufacturing Support at Tottori Institute of Industrial Technology
Kengo NOJIMA, 251
Digital Manufacturing Support by Mechanical and Electronics Research Institute, Fukuoka Industrial Technology Center
Kiyotaka SHUZENJI, Akihiko MURATA, Taiki YAMADA, Takafumi KIKUTAKE, Keiichi NISHIMURA, 258
Examples of Digital Manufacturing at Industrial Technology Center of Nagasaki
Naoki IRIE, Soichi SASAKI, 266
Papers (Published in J-STAGE)
Evaluation of Liquid Packaging Bag Transfer Using a Vacuum Suction Gripper with Link Mechanism
Tatsuya YOSHIDA, Fumiyasu KURATANI, Yuki FURUSAWA, Shintaro KAWAE, Tadashi AOKI, Toshihiro MOURI, Noriyuki TSUBOI, 271
The Effect of Electrode Shape between the Gap on Deep Hole Electrical Discharge Machining (EDM)
Atsutoshi HIRAO, Yoshitaka KATO, Wang CHENXUE, 281
Journal “Design Engineering” Vol.60, No.4 2025
Special Issue: Professional Engineer and Design
Explanations
What is Professional Engineer of Japan and Institution of Professional Engineers, Japan?
Hiroko MOURA, 179
Discovery and Practice of Design Concepts in Childhood
(Effects and Challenges of Science Experiment Classes for Children)
Hiroshi FUJIUCHI, 186
Case Studies of Engineer Education and Safety Education at Universities
Koichiro NAMBU, 192
The Significance of Design Calculations and SME Support: Insights from Professional Engineer Practices
Yoshihito SHIMANAKA, 196
Papers (Published in J-STAGE)
Experimental Development of Tyre Tread Design Combined with Parametric Search
Koki MORITA, Shogo HIRAO, Kazuki TAKENOUCHI, 205
Motion Analysis of Link Chains Induced from Spatial Prime Structures
Takahiro ARUGA, Nobuyuki IWATSUKI, Kotaro HOSHIBA, 217
Journal “Design Engineering” Vol.60, No.3 2025
Special Issue: Mobility Creation and Design 2
Explanations
Development and Design of Railway Rolling Stock
Shoji NISHIGAKI, 121
The Development History and Practical Application of the Next-Generation Tilt Control System
(From the Perspective of Actuator Development)
Akihito KAZATO, 129
Development Trends of ASV ‘KaiKoo’; Mobile Cell Site for Underwater Vehicles
Hiroshi MATSUMOTO, Takao SAWA, 135
Non-contact Type Climber for Space Elevator
Takayoshi NARITA, Hideaki KATO, 142
Papers (Published in J-STAGE)
Adhesive Strength Improvement of Butt Joint due to Duplicated Interaction of Additional Notch
Kazuhiro ODA, Marika TAKEO, Kazuki IDE, Noriko TSUTSUMI, Nao-Aki NODA, 149
Visualization of Gas-Liquid Two-Phase Flow in the Urea-SCR System Using High-Speed Camera
(Construction of the Visualization Experimental Equipment and the Influence Comparison of the Gas Temperature by PIV Analysis)
Naoki SUGIYAMA, Jyo ONO, Tetsuo NOHARA, Shotaro NARA, Yuki KAWAMOTO, Naoya FUKUSHIMA, Masayuki OCHIAI, 163
Journal “Design Engineering” Vol.60, No.2 2025
Special Issue: Mobility Creation and Design 1
Explanations
Learn Craftsmanship Through Activity of Student Formula
Kyohei SATO, 53
Engineering Design in Academia and in Actual Development
Makoto YAMAUCHI, 61
Vehicle Design and Manufacturing Management for Railway Operators
Tsuyoshi SUZUKI, 65
Pitfalls in Automotive Suspension Geometry Design
(Critical Review of the Roll Center Concept & Introduction of a Clearly Defined Roll Model)
Ikkei KOBAYASHI, Hideaki KATO, Takayoshi NARITA, 72
Papers (Published in J-STAGE)
Study on Springback Prediction Method in Rebar Bending
Satoshi HIGAKI, Ikuho MATSUKUMA, Tomoki GO, Masahiro SASADA, Tatsuya TANAKA, 81
Design and Development of Active-manual for Driver
(1st Report, Classification of Cognition by Proficient of Driving Support Equipment)
Naoki NISHIMURA, Hitoshi SOMA,
Yasushi YOKOYA, 97
Cooling Characteristics of Air-Cooled Cylinder with Fins with Slits under Forced Convection
(3rd Report, Cooling Effects of Number of Slits in Front)
Masao YOSHIDA, Kohei NAKASHIMA, Kento NISHII, Sota HIRAI, Shinya OZAKI, Nobuyuki OKURA, 109
Journal “Design Engineering” Vol.60, No.1 2025
Special Issue: Design Education Through Student Competitions
The New Year Greeting
Nobuyuki IWATSUKI, 1
Explanations
Additive Manufacturing Education for Students Through Design Competition
Hiroko SUZUKI, 2
KOSEN Material Contest
(Engineering Education to Inherit KOSEN, Material Engineering, and Culture)
Daisuke SASAKI, 7
Activities of “Casting Contest” for Young Engineers Development
Ken MOIZUMI, 16
Learning and Feeling Basic Design from Introduction to Manufacturing Creation
Kaoru MITSUHASHI, 20
Papers (Published in J-STAGE)
Analysis of Assembly Variation by Positioning Between Two Parts using a Hole and a Slot
(2nd Report, Derivation of the Radius of Circle Circumscribing the Rattling Area)
Shinya SUZUKI, Akimasa OTSUKA, Yuki KAWAGUCHI, Tohru KANADA, 27
Study on Lubrication Properties of Screw Tightening Lubricant PIB under Various Surface Roughness Conditions using ECR Method and In-situ Observation
Takefumi OTSU, Kyoichi KOMATSU, Shinji HASHIMURA, 39
Journal “Design Engineering” Vol.59, No.12 2024
Special Issue: Advanced Structures Realized by Additive Manufacturing
Explanations
Structural Analysis and Design for Lattice Structures
Kuniharu USHIJIMA, 565
Reduction of Residual Deformation of Metal additive Manufacturing by Lattice Structure Optimization
Akihiro TAKEZAWA, 571
Energy Absorption Structures Based on Origami Tessellation
Sunao TOMITA, 577
Graded Porous Structure Creatation with Metal Additive Manufacturing (Proposal of Rhizoid Porous Structure (RPS) and Its Application)
Masayoshi MIZUTANI, 583
Porous Structure for Shock Absorber Based on Voronoi Structure
Satoshi OKUBO, 590
Papers (Published in J-STAGE)
Thin Hole Creation inside a Hole by Means of Electrical Discharge Machining
Ryuta KUBOTA, Tohru ISHIDA, Akira MIZOBUCHI, 597
Development of Ball Screw having Asymmetric Thread Groove Form (2nd Report, Evaluation of Indentation Resistance and Fatigue Life)
Shoji NOGUCHI, Yoshihiro HAMADA, Tohru TAKAHASHI, 609
Research on Torque Characteristics of Small Ball Bearings under Grease Lubrication (Effect of Measurement Time on Torque of Extra Small Ball Bearings 608)
Masahiro HIGASHI, Shoji NOGUCHI, Tomoya HOTTA, 619
Erratum
Erratum: Project-Based Learning in Collaboration with a Local Company, in Vol. 59, No. 11, P. 551
631
Journal “Design Engineering” Vol.59, No.11 2024
Special Issue: New Relationship between Design and Materials
Preface
About Special Issue “New Relationship between Design and Materials”
Tamotsu MURAKAMI, 509
Explanations
Non-Metal Wheelchair
Hideyuki KITAMI, 510
Resin Thrust/Radial Bearing
Shuuichi NOWATARI, Atsuhiko HOTANI, Shigeo MIYAKE, 514
Robots and Electric Mobility Devices with Inflatable Structure
Ryuma NIIYAMA, 518
Verification of Carbon Dioxide Emission Reduction Effect and Durability Performance of New Material Made from Food Ingredients Only
Nami HASEGAWA, Kota MACHIDA, 524
Papers (Published in J-STAGE)
Influence of Die Shape and Configuration on the Elastic Deformation of Die in Cold Forging
Yoshimi MURATA, Yuichiro SUZUKI, 529
Effect of Initial Grease Filling State on Torque of Small Ball Bearing 6204
Masahiro HIGASHI, Shoji NOGUCHI, Tomoya HOTTA, 539
Note (Published in J-STAGE)
Project-Based Learning in Collaboration with a Local Company
Koichiro YAMADA, Kaoru TOYODA, Takao MUROMAKI, Kengo KIHARA, Haruki NITTA, 551