Home » 出版部会 (Page 2)
Category Archives: 出版部会
Journal “Design Engineering” Vol.59, No.6 2024
Special Issue: Application of Natural Language Processing in Design (2)
Explanations
Acquisition of Design Knowledge from Text such as Specifications and Defect Reports
Kazuhiro AOYAMA, 239
Advanced Design Technology Integration and Technology Management Strategies in Advanced Semiconductors
Kazuya OKAMOTO, 248
Support of DfX Learning and Upstream Design using Large Language Models
Tatsunori HARA, Taisei KAWAMURA, Jun OTA, 259
Assessment of Concept Similarity and Design Concept Generation based on Distributional Representation
Yutaka NOMAGUCHI, 266
Papers (Published in J-STAGE)
Research on Torque Characteristics of Small Ball Bearings under Grease Lubrication (Torque Current Status Investigation of Extra Small Ball Bearings 608)
Shoji NOGUCHI, Masahiro HIGASHI, Tomoya HOTTA, 275
Out-of-plane Crushing Characteristics of Bio-inspired Honeycomb Cores with Square Tubes
Yue BEN, Sachiko ISHIDA, Kazuya SAITO, Hiroshi OOKUBO, 287
Journal “Design Engineering” Vol.59, No.5 2024
Special Issue: Application of Natural Language Processing in Design
Explanations
Special Issue on “Application of Natural Language Processing in Design”
Yutaka NOMAGUCHI , 193
Current Status and Future Prospects of Natural Language Processing
Hidekazu YANAGIMOTO, 195
Natural Language Processing for Information Systems (NLP-assisted Design Process and LLM-featured System Design)
Shigeru HOSONO, 202
Methods for Suggesting Directions for Exploration and Exploitation in Product Design and Development
Masahiro OKAMOTO, Tamotsu MURAKAMI, 209
Basic Study on Supporting Idea Generation about Product Needs and Uses Using Natural Language Processing Techniques
Eiji MORINAGA, 216
Paper (Published in J-STAGE)
Development of a Force Sensor for a Neuroendovascular (Structure and Performance of the Improved Force Sensor)
Hiroki TADAUCHI, Yoshitaka NAGANO, Shigeru MIYACHI, Reo KAWAGUCHI, Tomotaka OHSHIMA, Naoki MATSUO, 223
Journal “Design Engineering” Vol.59, No.4 2024
Special Issue: Utilization of Multicopters and Design of Supporting Equipment of Multicopters
Explanations
Design of a High-Sensitivity Air-coupled AE Sensor for Non-Contact AE Measurement for Infrastructure by Drone
Takuma MATSUO, 147
Case Studies on the Use of Multicopter for Ecological Surveys on Uninhabited Islands in the Ogasawara Islands
Kazuto KAWAKAMI, 152
Consideration of Mechanical and System Design Based on Multicopter Operation
Keisuke KATO, Takuma MATSUO, 157
The Opportunities of Autodesk® Fusion® Generative Design
Shimon TANAKA, Takahiro CHINO, Tomoyo WATANABE, Tsubasa NAKAMURA, 164
Paper (Published in J-STAGE)
Estimations of Cavitation Pressures in Dimpled Seal-type Thrust Bearings
Reo MIWA, Ryota ISHII, Norifumi MIYANAGA, Atsushi TSUJIMORI, Jun TOMIOKA, 169
Note (Published in J-STAGE)
Effects of Different Corrosion Environment and Different Welding Condition on the Residual Strength of Weld Part of the Stainless Steel
Kazunori ISHITSUKA, Tsuyoshi TAKAHASHI, Katsuhiko SASAKI, 183
Journal “Design Engineering” Vol.59, No.3 2024
Special Issue: Current Status and Future of Design Engineering Education in Tohoku Region
Explanations
Efforts in CAD/CAM Education at University (Introduction of 5-axis Machining using Machining Center)
Akinori SAITO, 99
3D Design & 3D Print Contest for High School Students (High School and University Collaboration in the Department of Mechanical Engineering, Akita Prefectural University)
Takehiko TAKAHASHI, Eiichi SAKAI, Satoru TSUGAWA, 106
Current and Future of Design and Drawing Education at Universities (Case Study at Yamagata University)
Tatsuya OHMACHI, 113
Paper (Published in J-STAGE)
Lubrication Properties of Silicone Oil between POM and Chromium Molybdenum Steel under Reciprocating Sliding
Manabu SUZUKI, Yoshinori TAKEICHI, 119
Note (Published in J-STAGE)
Development of Extended Components for Industrial Robots Using Generative Design and Additive Manufacturing Technology
Sai MADOKORO, Koji GOTOH, 133
Journal “Design Engineering” Vol.59, No.2 2024
Special Issue: Gears from the Past to the Latest Technology
Explanations
Gearing Your Past to Power Your Future (Learn from the History of Gear Technology, Live Today, Hope for Tomorrow)
Keiji SONODA, Kazuki TAKENOUCHI, 49
Introduction of Gear Research in Saga University
Fumihiro OHSHIMA, 58
The Latest Technologies for Gear Manufacturing
Koichiro URIU, 63
Vibration Cutting for Gear Processing
Shu KARUBE, 68
Paper (Published in J-STAGE)
A Method for Detecting Missing Data in Point Clouds Using Morphological Operations
Yuji TESHIMA, Ryo NAKAO, Asahi MATSUDA, Hideki SHIMADA, Kazuyuki KANEDA, Yuta MURAKI, Ken-ichi KOBORI, 75
Note (Published in J-STAGE)
Effect of Weld Deformation on Coaxiality of Scroll Compressor Bearings
Tsutomu NOZAKI, Takeshi KONO, 87
Journal “Design Engineering” Vol.59, No.1 2024
Special Issue: Recent Technology and Research Trends in Rolling Bearings
Preface
The New Year Greeting
Nobuyuki IWATSUKI, 1
Explanations
Recent Technology and Research Trends in Rolling Bearings
Shoji NOGUCHI, 2
Low Torque Technologies for Rolling Bearings with Grease Lubrication
Michita HOKAO, 8
Lubrication Condition Monitoring in EHD Contacts (Development of the Electrical Impedance Method)
Taisuke MARUYAMA, 13
Development of Sensor Integrated Bearing for Condition Monitoring (Introduction of Specifications and Performance Evaluation)
Yasuyuki FUKUSHIMA, 19
Condition Monitoring Technology for Rolling Bearings Using Acoustic Emission Sensing
Alan HASE, 24
Paper (Published in J-STAGE)
Investigation of the Productivity and Improving the Accuracy Utilizing Heat Conduction Laser Welding Robot of Sheet Metal Parts for Machine Tools with Supporting Mortise and Tenon Joint
Yohei YAMAGUCHI, Toshiki HIROGAKI, Eiichi AOYAMA, 31
Journal “Design Engineering” Vol.58, No.12 2023
Special Issue: Actuator Design for Control System Construction
Explanations
Application and Design of Actuators using Giant Magnetostrictive Materials
Taro KATO, Hideaki KATO, 523
Design of Active Seat Suspension Focused on Improvement of Ride Comfort of Vehicles
Keigo IKEDA, Ayato ENDO, 529
Modeling of Magnetic Levitation System and Design of Normal Conducting Electromagnet
Kazuki OGAWA, 536
Design for Actuators Used to Drive Valve System of Spark-Ignition Engines
Jumpei KURODA, Takayoshi NARITA, Hideaki KATO, 543
Paper (Published in J-STAGE)
Passive Exercise Device for Pronation and Supination Movements of Forearm using Pneumatic Soft Actuators
Daigo ISHII, Hironari TANIGUCHI, 549
Note (Published in J-STAGE)
Analyzing Welding Deformation Factors in Scroll Compressors
Tsutomu NOZAKI, Takeshi KONO, 565
Journal “Design Engineering” Vol.58, No.11 2023
Special Issue: Design of Growth
Explanations
Use Your Instinct
Shuichi FUKUDA, 457
How do Designers Improve Their Creativity? (My Twenty-Two Years Struggle for Education of Creative Design and the Student’s Improvement of Creativity after the Education)
Masayuki NAKAO, 462
Design Theory for Value Growth Design (Methodology for Timeaxis Design Considering Multi-time scales)
Akinari HIRAO, Takeo KATO, Yoshiyuki MATSUOKA, 471
Science of Hyper-Adaptability and its Prospects for Design Applications
Jun OTA, 477
Emotion Mechanics and Exploration Cycle (Mathematical Principle of Interest and Curiosity)
Hideyoshi YANAGISAWA, 484
Paper (Published in J-STAGE)
Effects of Visual Stimulation by Lighting with Chromatic Colors on Thermal Sensation and Task Performance
Mikoto SAITO, Tsuyoshi KAWANAMI, Masato INOUE, 493
Note (Published in J-STAGE)
Creative Design and Design Review on Mechanical Design and Drawing (Manufacturing and Collaborative Classes between National Institute of Technology (KOSEN))
Koichiro YAMADA, Kaoru TOYODA, Takao MUROMAKI, Atsushi SUDA, 511
Journal “Design Engineering” Vol.58, No.10 2023
Special Issue: Design Education through the Design Competition for KOSEN Students 2
Explanations
Introduction of the Best Award Work of the Kosen Design Competition Additive Manufacturing Design Category
Naotsugu UNO, 427
The Process of Creating a Fictitious Architectural Perspective (The Grand Prize-Winning Work of the Pre-Dezacon, Spacial Design Field)
Shugo KUDO, Jitsuro MASE, 432
Pre-Design Competition Award-Winning Works
Kinya TANIGAMI, 436
Paper (Published in J-STAGE)
Development of Lubricating Oils Photography Equipment Toward the Creation of Degradation Diagnosis Technology Using Color by Lubricating Oil Image Analysis
Shuya NAKAMURA, Tomomi HONDA, Tomohiko KON, Genki OKUYAMA, Hiroki SEKIGUCHI, Masahiro KOBESSHO, 441
Journal “Design Engineering” Vol.58, No.9 2023
Special Issue: Design Education through the Design Competition for KOSEN Students 1
Explanations
On The History and Future of The Design Competition for KOSEN Students
Takayuki TAMAI, Takahiro TAMURA, 383
Introduction of the Winning Work in the Structural Design Category
Yukio KITANO, 389
Introduction of the Best Entries in the Space Design Category
Yuki TOYOSHIMA, 393
Introduction of Grand Prize Winner in Creative Design Category (Yosakoi Made From The Town)
Megumi KITAYAMA, 397
Note (Published in J-STAGE)
Basic Study of Weld Deformation Analysis of Scroll Compressor Chamber
Tsutomu NOZAKI, Takeshi KONO, 403
Paper (Published in J-STAGE)
Convenient Formulas to Provide Accurate Stress Intensity Factor Distributions of a Semi-Elliptical Surface Crack Subjected to Shear Loading
Yasushi TAKASE, Nao-Aki NODA, 415